ATMEGA1284P – AU Microcontroller – (SMD Package) – TQFP – 44 Pin Microcontroller

The ATMEGA 1284P is a low-power CMOS 8-bit microcontroller based on the AVR enhanced RISC architecture. By executing powerful instructions in a single clock cycle, the ATMEGA1284P achieves through puts approaching 1 MIPS per MHz allowing the system designer to optimize power consumption versus processing speed. It is a 8-bit Microcontroller with 128K Bytes In-System Programmable Flash.

Features:-

• High-performance, low-power 8-bit Atmel® AVR® Microcontroller

• Advanced RISC architecture

̶  131 powerful Instructions

– most single-clock cycle execution

̶ 32 × 8 general purpose working registers

̶  Fully static operation

̶  Up to 20MIPS throughput at 20MHz

̶  On-chip 2-cycle multiplier

• High endurance non-volatile memory segments

̶  16/32/64/128KBytes of In-System Self-programmable Flash program memory

̶  512/1K/2K/4KBytes EEPROM

̶  1/2/4/16KBytes Internal SRAM

̶  Write/Erase Cycles: 10,000 Flash/ 100,000 EEPROM

̶  Data retention: 20 years at 85°C/ 100 years at 25°C(1)

̶  Optional Boot Code Section with Independent Lock Bits

• In-System Programming by On-chip Boot Program

• True Read-While-Write Operation

̶ Programming Lock for Software Security

• Atmel QTouch® library support

̶  Capacitive touch buttons, sliders and wheels

̶  QTouch and QMatrix acquisition

̶  Up to 64 sense channels

•  JTAG (IEEE std. 1149.1 Compliant) Interface

̶  Boundary-scan Capabilities According to the JTAG Standard

̶  Extensive On-chip Debug Support

̶  Programming of Flash, EEPROM, Fuses, and Lock Bits through the JTAG Interface

•  Peripheral Features

̶  Two 8-bit Timer/Counters with Separate Prescalers and Compare Modes

̶  One/two 16-bit Timer/Counter with Separate Prescaler, Compare Mode, and Capture      Mode

̶  Real Time Counter with Separate Oscillator

̶  Six PWM Channels

̶  8-channel, 10-bit ADC

•  Differential mode with selectable gain at 1×, 10× or 200×

̶  Byte-oriented Two-wire Serial Interface

̶  Two Programmable Serial USART

̶  Master/Slave SPI Serial Interface

̶  Programmable Watchdog Timer with Separate On-chip Oscillator

̶  On-chip Analog Comparator

̶  Interrupt and Wake-up on Pin Change

• Special Microcontroller Features

̶  Power-on Reset and Programmable Brown-out Detection

̶  Internal Calibrated RC Oscillator

̶  External and Internal Interrupt Sources

̶  Six Sleep Modes: Idle, ADC Noise Reduction, Power-save, Power-down, Standby and      Extended Standby

•  I/O and Packages

̶  32 Programmable I/O Lines

̶  40-pin PDIP, 44-lead TQFP, 44-pad VQFN/QFN/MLF

̶  44-pad DRQFN – 49-ball VFBGA

•  Operating Voltages

̶  1.8 – 5.5V

•  Speed Grades

̶  0 – 4MHz @ 1.8 – 5.5V

̶  0 – 10MHz @ 2.7 – 5.5V

̶  0 – 20MHz @ 4.5 – 5.5V

•  Power Consumption at 1MHz, 1.8V, 25° C

̶  Active: 0.4mA

̶  Power-down Mode: 0.1µA

̶  Power-save Mode: 0.6µA (Including 32kHz RTC)

* product image for illustration purposes only. actual product may vary.